![64053 boost gauge kit 64053 boost gauge kit](https://www.evasivemotorsports.com/mm5/graphics/00000001/MM-01010-AP1-MR01.jpg)
#64053 boost gauge kit install#
Remove the plug and install the straight fitting provided into the threaded hole with Teflon thread-sealer. Ford/Navistar 7.3L IDI diesel with factory turbo - Locate the 1⁄8" NPT pipe plug in the spiral pressure chamber. Install the straight fitting provided into the threaded hole with Teflon threadsealer.
![64053 boost gauge kit 64053 boost gauge kit](https://gbodyparts.com/images/thumbs/250x250_Air_Fuel_Guage.jpg)
Secure the tubing to other tubing inside the engine compartment with cable ties.įord/Navistar 6.9L/7.3L IDI diesel with Banks Sidewinder turbo - Locate the 1⁄8" NPT threaded hole in the pressure chamber. TUBING INSTALLATION All gauge tubing should be routed away from heat sources such as exhaust manifolds or piping, and away from sharp edges. On some Cummins C8.3L applications, it may be necessary to remove a 1⁄2" NPT pipe plug from the inlet casting and install a reducer bushing.Ĭhevrolet/GMC 6.2L/6.5L diesel with Banks Sidewinder turbo - Locate the 1⁄8" NPT threaded hole in the pressure chamber. Install the straight fitting at this location, using Teflon threadsealer on the pipe thread end of the adapter fitting. In pusher motorhomes, it is on the passenger-side. NOTE: In Dodge pickups this plug is on the driver-side.
#64053 boost gauge kit manual#
Refer to the Owners Manual for your Banks system to determine maximum boost specifications for your specific application.Ĭummins B5.9L/C8.3L diesel with factory turbo - Locate and remove the 1⁄8" NPT pipe plug on the side of the intake manifold as shown in Figure 2. Use a Teflon thread-sealer on fitting pipe threads.īOOST GAUGE ADAPTER FITTING LOCATION Boost levels vary widely, depending on the engine and turbocharger configuration. Install straight fitting, supplied, into hole tapped in air inlet casting. Tighten loose clamps and reinstall the brace. Use of a new gasket is recommend for reinstallation of the air inlet casting on intake manifold. Center-punch this location and drill through the casting wall with a 0.399-diameter letter R drill. Measure and mark the air inlet casting as shown in Figure 1. Once the gauges are wired and secured to the console according to the following instructions, attach the console assembly to the console adapter using the two machine screws provided. Remove the backing from the adhesive Velcro tape on the bottom of the console adapter, position the console adapter and press down firmly. ON TOP OF DASH - Wipe the dash-top with an alcohol pad or other surface cleaner. UNDER DASH - Using the panel as a template, drill two 3⁄16" diameter holes in the dash and mount the panel with two 10 x 1⁄2" machine screws, nuts, and star-washers provided. Cover the intake manifold opening to prevent foreign objects or debris from falling into engine.
![64053 boost gauge kit 64053 boost gauge kit](https://i.ebayimg.com/images/g/HQoAAOSwq2xcGJSO/s-l225.jpg)
WARNING! Foreign matter in the intake manifold can cause serious engine and/or turbocharger damage upon engine start-up. Unbolt and remove the air inlet casting from the top of intake manifold. Remove the connecting strap between turbocharger and air inlet casting. Be certain the instruments can be viewed conveniently by the driver.Ĭhevrolet/GMC 6.5L diesel with factory turbo - Loosen the hose clamp on the compressor discharge of the turbocharger. INSTALLATION PROCEDURE GAUGE PANEL INSTALLATION Choose a suitable location under the lower edge of the dash panel for mounting the instrument panel, or on top of the dash for the molded instrument console. Route or tie all wires a minimum of 6 inches from hot exhaust parts eight or more inches is recommended where possible. moving parts, and sharp edges that may cause cuts Position wires and hoses away from exhaust heat,ģ.
![64053 boost gauge kit 64053 boost gauge kit](https://ae01.alicdn.com/kf/H122fa3215569438da5ae7c40f2380057O/s-2-52mm-7-Color-LED-Electrical-Car-PSI-Turbo-Boost-Gauge-Meter-With-Sensor-and.jpg)
Do not use concrete blocks or other masonry items that may collapse under the vehicle weight. Never perform any work under a vehicle supported only by its service jack or a hydraulic jack. Ramps of adequate capacity for the vehicle’s weight. wheels, it should be supported by safety stands or IMPORTANT! Anytime the vehicle is raised off itsĢ. If you cannot correspond your vehicle to the text provided, please contact Customer Service at (626) 969-9600 for assistance. For proper installation, select the text and illustrations that closest correspond to your vehicle. NOTE there are portions of the installation procedure and certain illustrations matched to specific vehicle types. Installation and to determine what additional tools or materials you will need, read the entire 8–page manual before starting any work. GENERAL INSTALLATION PRACTICES This manual is an installation guide for allġ. Gale banks engineering 546 duggan avenue This manual is for use with systemS 64050-64054